Large Capacity Hard Wood Charcoal Making Carbonization Furnace For BBQ Charcoal Making
Our Advantages
1.Our engineer New Design Hoist Equipment. It's more easy and convenient and safe for loading and uploading. Only Mingyang factory equips the new device!
2.What we use is National Standard raw material ,which specially used in Carbonization Furnace.
3.Combustible gas recovery device, through this device we can release excess gas to confirm charcoal will not be undue carbonized and you can get nice quality charcoal. You also can make use of excess gas to heat and warm.
4.31 years experience of carbonization furnace. In our factory,more than 80% workers has more than 8 years experience.
Model | Capacity | Inner volume | Temperature | Machine configuration |
QHL-1 | 1.5-2 t/24h | 2.75*3CBM | 400-600 degree | 1 outer stove,3 inner stoves with 3 caps,one 3t lifting device, 1smoking tank |
QHL-2 | 3-4 t/24h | 2.75*6CBM | 400-600 degree | 1 outer stove, 6 inner stoves with 6caps, one 5 tons hoisting equipment with motor, 1 smoking tank |
QHL-3 | 4.5-6 t/24h | 2.75*9CBM | 400-600 degree | 3 outer stove, 9 inner stoves with 9 caps, one 5 tons hoisting equipment with motor, 1 smoking tank |
QHL-4 | 6-8 t/24h | 2.75*12CBM | 400-600 degree | 4 outer stove, 12 inner stoves with 12 caps, one 5 tons hoisting equipment with motor, 4 smoking tank |
Product Details of Wood Sawdust Briquettes Carbon Kiln
This is our personal design,which greatly increased carbonizing ratio (from88% to 99%) and shorten the carbonization time from about 24 hours to 6-8 hours.This machine's feature is easy to operate and maintainance,higher safty,high efficiency,continuiously working performance energy-saving and environment protection.
This type of stove adopts the structure of unique air storage chamber to fully reuse the smoke produced during the process of carbonization And 95% of the redundant smoke can be used in drying and carbonizing ,saving much fuel during the whole process,and prompt the quality of the final products.
Working Principle of Wood Sawdust Briquettes Carbon Kiln
When one inner stove have been finished carbonization, we will use the hoisting tools to hoist the inner stove out of the outer stove, then put down the inner stove on earth for natural cooling, at the same time, we can put another inner stove into the outer stove for the second carbonization,which will save a lot of time, so the productivity increase a lot, it is the ideal choice for mass production of charcoal.
Structure of Wood Sawdust Briquettes Carbon Kiln
Outer Stove
It includes heating room (for heating the stove), furnace body and heat-keeping layer (it is made of the heat insulating material, used for keep the heating)
Inner stove
It includes the stove tank body and the sealed top cap.Both of them are made of heat resistance thermal steel,and the three carbonization baskets can be stack together,
easy for loading and transporting ,and it will save a lot of space and transport charge.
Purification tank
When during the process of carbonizing, there will be some smoke( can be burning) the smoke can return to the furnace through tube for purifying, after purification , the combustible smoking can be flow into the heating room of the outer stove for heating the stove again;
Hoisting equipment
We design new hoist equipment. It's more easy and convenient to loading. It includes the steel hoisting frame and the E-hoist .And it is easy for loading and unloading the stove, and can reduce labor intensity.
Combustible gas recovery device, through this device we can release excess gas to confirm charcoal will not be undue carbonized and you can get nice quality charcoal. You also can make use of excess gas to heat and warm.
Working Process of Wood Sawdust Briquettes Carbon Kiln
1)Preparation
Open the lid of carbonization furnace, lift out the inner tank, put raw material in, then put the inner tank back. Close the lid then seal it so that no oxygen could come inside.
2)Heating
After sealing process, use wood waste or gas to heat furnace from the bottom. After 10 minutes burning, the temperature reaches 90℃, turn to use slow fire to heat. This process will take 60-120 minutes to reduce water vapor from your materials.
3)Carbonization
Keep heating, after the temperature reaches 180-235 ℃, the raw material will produce flammable gas from the inner tank. Reuse the gas as fuel to heat the inner tank. The whole process will last about 8 hours. When the temperature reaches highest and no flammable gas is produced, the carbonization process is finished.
4)Cooling
Lift the inner tank out. Let it cool naturally. The longer cooling time is, the better quality of charcoal is. After about 10 hours, you can take charcoal out.
Raw Material of Wood Sawdust Briquettes Carbon Kiln
Raw material can be Wood log, tree, tree branch, wood briquette, coconut shell, palm nutshell, Walnut Shell, Macadamia nutshell, bamboo, and other nut shell or hard raw material
Related Hot Product of Wood Sawdust Briquettes Carbon Kiln
https://message.alibaba.com/message/default.htm
Company Profile
Gongyi Xiaoyi MingYang Machinery Plant was founded in 1988, is a manufacture of new energy-saving environmental protection equipment.
In the twenty years of development, our factory brings together elte of this field, and use professional technics to build the equipment. "Ming Yang Machinery" from a single charcoal machine and equipment to production equipment series, with three series of more than 30 machinery products. Have exported to britain, Russia, Sweden, Malaysia, Indonesia,Vietnam and other countries, more than 30 countries and regions.
Manufacturing quality products for industy, and create value for society!
Gongyi MingYang Machinery warmly welcome new and regular customers to visit and guidance.
Contact Person : | Stella Zhang |
---|